American-power-conversion NS 600 User Manual download pdf

Back-UPS NS 600

User’s Guide

Connect Battery

Equipment

Power On and

Install Software

All other trademarks are property of their respective owners.

Surge Protection

These outlets provide full-time protection from surges even if the

Back-UPS NS is switched OFF. Plug your printer, fax machine,

scanner, or other peripherals that do not need battery power into

these outlets.

Battery Back-up plus Surge Protection

These outlets are powered whenever the Back-UPS NS is

switched ON. During a power outage or other utility problems

(brownouts, over-voltages), these outlets will be powered for a

limited time by the Back-UPS NS. Plug your computer,

monitor, CD-ROM drive and one other data-sensitive device

such as an external disk or tape drive, or Home Phoneline

Networking Association (HPNA) device into these outlets.

Press the ON/OFF switch to power the unit

ON.

A single short beep and the green “Power”

indicator confirms the Back-UPS NS is on and

ready to provide protection.

The Back-UPS NS should charge for at least 16

hours to ensure sufficient runtime. The unit is

being charged whenever it is connected to utility

power, whether the unit is turned ON or OFF.

If the red Building Wiring Fault indicator (located

on the end near the power cord) is lit, your

building wiring presents a shock hazard that

should be corrected by a qualified electrician.

Install the PowerChute

Personal

Edition

software

Place the PowerChute Personal Edition CD-

ROM into your computer and follow the

installation instructions on the screen.

.apc.com

APC, Back-UPS and PowerChute are registered trademarks of American Power Conversion Corp.

Status Visual Indicators Audible Indicators Alarm Terminates

When

On Line - UPS is supplying conditioned

utility power to the load.

Power LED - ON None n/a

On Battery - UPS is supplying battery

power to the load connected to the

Battery outlets.

Power LED - ON

(off during beep)

Beeping 4 times

every 30 seconds

UPS transfers back to

On Line operation, or

when UPS is turned

off.

Low Battery Warning - UPS is supplying

battery power to the load connected to

the Battery outlets and the battery is near

exhaustion.

Power LED - Flashing Rapid beeping (half-

second intervals)

UPS transfers back to

On Line operation, or

when UPS is turned

off.

Replace Battery - Battery needs to be

checked and/or replaced, or battery is not

connected.

Power LED - Flashing Constant tone UPS turned off with

the power switch.

Overload Shutdown - During On Battery

operation a battery power supplied outlet

overload was detected.

Power LED - OFF Constant tone UPS turned off with

the power switch.

Sleep Mode - During On Battery

operation the battery power has been

completely exhausted and the UPS is

waiting for utility power to return to

normal.

Power LED - OFF Beeping once every

4 seconds

Utility power is

restored, or if utility

power is not restored

within 32 seconds, or

the UPS is turned off.

Building Wiring Fault - Your building

wiring presents a shock hazard that

should be corrected by a licensed

electrician.

Building Wiring Fault

LED (red) - ON

None UPS is unplugged, or

plugged into a

properly wired outlet.

Status Indicators

Power

Circuit

Breaker

AC Line

Cord

Building Wiring

Fault Indicator

UPS Power

Indicator

Power

Switch

See the Troubleshooting section for additional assistance.

For safety, the Back-UPS NS is shipped with one battery wire disconnected. The UPS will not operate until the wire is connected to the touch-safe

battery terminal. NOTE: Small sparks may occur during battery connection. This is normal.

Turn the Back-UPS NS over and press in the

two release tabs. Slide the plastic battery

cover off the unit.

Insert the battery back into the compartment.

Slide the plastic battery cover in place until the

two tabs lock into place.

Connect the battery wire firmly to

the battery terminal.

1 2 3

Plastic Battery

Cover

Release Tabs

Battery Wire

Battery Terminal

Connect

Connect Modem / Phone / DSL / Fax / HPNA to Surge Protection

The Back-UPS protects a single line (2-wire) phone (including Digital Subscriber Line -

DSL), Home Phoneline Networking Association (HPNA) type equipment, modem, or

fax machines from surges when connected through the UPS as shown below.

Place the Back-UPS NS to avoid:

- Direct sunlight

- Excessive heat

- Excessive humidity or contact with fluids

Plug the Back-UPS NS power cord directly into a wall outlet; not a surge

protector or power strip.

Connect Computer Cable

The supplied cable and software provide automatic file saving and shutdown of the

operating system in the case of a sustained power outage.

Connect the cable to the Data Port of the Back-UPS NS. Connect the other end of the

cable to the USB port on your computer. The software will automatically find the USB

Port of your computer.

DSL / MODEM /

WALL

TO COMPUTER USB PORT

FROM WALL JACK

DATALINE OUTPUT TO DSL,

MODEM, PHONE,

OUTLET

DATA PORT

FAX

Power

Battery Backup plus Surge Protection

Surge Protection

The Back-UPS NS indicates operating status

using a combination of visual and audible

indicators.

1 2

Back-UPS NS 600 1

Summary of Contents

Page 1 - Back-UPS NS 600

Page 2

TroubleshootingUse the table below to solve minor Back-UPS NS installation or operation problems. Consult APC Online Technical Support or call APCTech

Comments to this Manuals

No comments

American-power-conversion NS 600 User Manual

Browse online or download User Manual for Tools American-power-conversion NS 600. American Power Conversion NS 600 User Manual

Summary of Contents

Comments to this Manuals

Related products and manuals for Tools American-power-conversion NS 600