American Power Conversion BH500NET User Manual download pdf

INSTALLATION

.apc.com

Back-UPS HS 500

User’s Manual

990-9234A 5/07

Remove Battery (if wall-mounting - if not proceed at Step 5)

32 - 104

F (0 - 40

Placement

Remove Connector Cover

Disconnect battery

wires from battery.

Caution: To prevent damage to the ribbon cable (not shown)

that connects the cover to the UPS, replace the cover after

removing the battery. Do not disconnect the ribbon cable

from the cover or the UPS.

Remove battery.

Press cover release

tab (one each side)

and remove cover.

Press the outlet cover release

tab (one each side); and pivot

cover off the unit.

Phone Line Out

.apc.com

Mount Back-UPS (optional)

Wall Anchor

Mounting

Hole

Wall

Connect and Install Battery, Install Battery Cover

Install battery cover.

Press the outlet cover

release tab (one each

side); and pivot cover

off the unit.

Connect and install

the battery..

Connect Cable Modem,

Circuit Breaker

Push to Reset

Cable Out

Input:

120V~, 10A, 50-60Hz

Cable In

From Cable Provider

(Phone, Internet,

and/or CATV; or

DSS)

To Cable Modem,

VCR, DSS or TV

Cable Box

Connect Phone Line

LAN

NetworkModem/Phone/Fax

RJ-45

Connectors

(will accept RJ-11)

RJ-45

Connectors

Phone Line In

(Standard or

DSL)

From Network Device

(or Computer Using a

Crossover Cable)

From Modem

DSS or CATV Receiver

8 10

Install Connector Cover

Align the holes in the

cover with the connector

cover release tabs (one

each side) and lower

connector cover.

(optional)

or DSL to Surge

Connect Network

Equipment

To Hub or

Router

Connect to Power Source

and Switch on UPS Power

Connect Equipment

Hub

or Router

Modem

Network Device

Output 1

Output 2

Output 3

Power Cords

Check the Building Wiring Fault indicator. If this

light emitting diode (LED) is illuminated, it is an

indication that a potential shock hazard exists. Have

the building wiring inspected and repaired by a

qualified electrician.

Building Wiring

Fault Indicator

Check the Building

Wiring Fault Indicator

to Surge Protection

Protection (optional)

NOTE: APC recommends your network equipment

(computer, modem, router, hub, or other networked

devices) be completely installed, configured, and

tested prior to adding this UPS to the network.

1 2 3 4

Summary of Contents

Page 1 - Back-UPS HS 500

INSTALLATIONw w w.apc.com®Back-UPS HS 500User’s Manual990-9234A 5/073Remove Battery (if wall-mounting - if not proceed at Step 5)32 - 104oF (0 - 4

Page 2 - INSTALL AND SETUP SOFTWARE

There are six status indicators (lights) on the front panel of the Back-UPS (On Line, On Battery,Overload, Replace Battery, TX/RX, and ACT/LNK).On L

Page 3 - Specifications

8. Following installation, the Back-UPS HS software is available in the Startmenu. Upon launching the program, it searches for all Back-UPS HS devices

Page 4 - APC Contact Information

Replace with an APC qualified battery. Replacement batteries can be ordered from APC Global Services. Have yourBack-UPS HS model number available when

Comments to this Manuals

No comments

American Power Conversion BH500NET User Manual

Browse online or download User Manual for Uninterruptible power supplies (UPSs) American Power Conversion BH500NET. American Power Conversion BH500NET User's Manual [da]

Summary of Contents

Comments to this Manuals

Related products and manuals for Uninterruptible power supplies (UPSs) American Power Conversion BH500NET