American-power-conversion PDU User Manual

Installation and Start-Up150kW InfraStruXureTM SystemLarge Data Centers480 V/ 600V Input

2 150kW InfraStruXure System—Installation and Start-Up WarningsReceiving/movingDo not tilt the PDU greater than 45° from its vertical axis. Never lay

Safety: Warnings150kW InfraStruXure System—Installation and Start-Up 3Total Power Off1. Set the PDU Main Input to OFF.2. Set the upstream power sourc

Safety: Warnings4 150kW InfraStruXure System—Installation and Start-Up EMIThis equipment has been tested and found to comply with the limits for Class

150kW InfraStruXure System—Installation and Start-Up 5Site PlanningDimensionsInfraStruXure PDUNetShelter VX Enclosure81in (2060mm)7.2in(183mm)Without

6 150kW InfraStruXure System—Installation and Start-Up Space ConsiderationsStudy the figure below to determine your space requirements for installing

150kW InfraStruXure System—Installation and Start-Up 7Weight ConsiderationsEnsure that the floor and sub-floor can support the total weight of the co

8 150kW InfraStruXure System—Installation and Start-Up Heat Output Consider the heat dissipation ratings of equipment to determine cooling requirement

150kW InfraStruXure System—Installation and Start-Up 9Electrical Requirements and SpecificationsProcedures requiring a licensed electricianElectrical

10 150kW InfraStruXure System—Installation and Start-Up Emergency Power Off (EPO)OverviewTo provide a mechanism for emergency power off, attach a remo

150kW InfraStruXure System—Installation and Start-Up 11Basic Installation ProcedureThis section provides the basic steps that you need to perform whe

208/480/600V

Site Planning: Basic Installation Procedure12 150kW InfraStruXure System—Installation and Start-Up 8. Install Shielding Troughs, Shielding Partitions,

150kW InfraStruXure System—Installation and Start-Up 13Installation ProceduresLevel the PDU and NetShelter EnclosuresLeveling feet are attached under

14 150kW InfraStruXure System—Installation and Start-UpConnect the Power Source to the PDUAccess the PDU Main Input breakerOpen the back doors of the

Installation Procedures: Connect the Power Source to the PDU150kW InfraStruXure System—Installation and Start-Up 15– In the top of the PDU for overhea

Installation Procedures: Connect the Power Source to the PDU16 150kW InfraStruXure System—Installation and Start-UpRoute the input conductors to the M

150kW InfraStruXure System—Installation and Start-Up 17Connect an Emergency Power Off SwitchOverviewConnecting the switch. The Emergency Power Off (EP

Installation Procedures: Connect an Emergency Power Off Switch18 150kW InfraStruXure System—Installation and Start-UpConnect an EPO switch to the user

Installation Procedures: Connect an Emergency Power Off Switch150kW InfraStruXure System—Installation and Start-Up 193. Test the EPO switch to ensure

Installation Procedures: Connect an Emergency Power Off Switch20 150kW InfraStruXure System—Installation and Start-UpSafety warningsHazardous voltage

150kW InfraStruXure System—Installation and Start-Up 21Connect User Input Contacts and Relay Outputs to the User Connection PlateOverviewMake contact

150kW InfraStruXure System—Installation and Start-Up iAbout this Manual This manual is intended for APC Field Service Engineers or APC-trained install

Installation Procedures: Connect User Input Contacts and Relay Outputs to the User Connection Plate22 150kW InfraStruXure System—Installation and Star

150kW InfraStruXure System—Installation and Start-Up 23Install Shielding Troughs, Shielding Partitions, and Cable LaddersShielding Troughs and Shieldi

Installation Procedures: Install Shielding Troughs, Shielding Partitions, and Cable Ladders24 150kW InfraStruXure System—Installation and Start-UpShie

150kW InfraStruXure System—Installation and Start-Up 25Install InfraStruXure Rack-Mount DevicesInstall the Rack Automatic Transfer Switches (ATS)Insta

26 150kW InfraStruXure System—Installation and Start-UpRoute and Attach Overhead WiringRoute and attach power cables to equipment racksIf you ordered

Installation Procedures: Route and Attach Overhead Wiring150kW InfraStruXure System—Installation and Start-Up 27– For dual feed devices within a redun

Installation Procedures: Route and Attach Overhead Wiring28 150kW InfraStruXure System—Installation and Start-Up5. From each NetShelter VX Enclosure,

150kW InfraStruXure System—Installation and Start-Up 29Wiring Under the FloorIf you are routing power cables to the enclosures under a raised floor, y

Installation Procedures: Wiring Under the Floor30 150kW InfraStruXure System—Installation and Start-Up5. At the circuit breaker panel, cut the wires t

150kW InfraStruXure System—Installation and Start-Up 31Route Data Cables to the InfraStruXure Manager Hub (or Switch)1. Connect a Cat-5 network cable

150kW InfraStruXure System—Installation and Start-Up 33Start-Up ProcedureSafety warningsThis section provides instructions on how to perform a system

Start-Up Procedure34 150kW InfraStruXure System—Installation and Start-Up3. Set the Main Output circuit breaker on the front of the PDU to OFF.

Start-Up Procedure150kW InfraStruXure System—Installation and Start-Up 35Apply power to the system1. Set the upstream input circuit breaker (utility o

Start-Up Procedure36 150kW InfraStruXure System—Installation and Start-Up4. Set the Main Output circuit breaker on the PDU to ON. 5. Close (turn ON) t

150kW InfraStruXure System—Installation and Start-Up 37Configure the InfraStruXure ManagerOnce all equipment is installed, the network cables are conn

150kW InfraStruXure System—Installation and Start-Up 39Appendix A: OperationHow to Apply Power to the SystemThis procedure instructs on how to apply p

Appendix A: Operation40 150kW InfraStruXure System—Installation and Start-Upb. Close (turn ON) the PDU distribution panel circuit breakers.NoteWhen th

150kW InfraStruXure System—Installation and Start-Up 41How to Ensure Total Power Off1. Open (turn OFF) the main circuit breaker on the power source fe

Contents150kW InfraStruXure System—Installation and Start-Up iiiSafety ...1Overview

Index150kW InfraStruXure System—Installation and Start-Up 43AApplying power to the system 33–34, 37–38Automatic transfer switches, installing 25CCabl

44 150kW InfraStruXure System—Installation and Start-Up UUpdates, to this manual iWWarnings 2–4Wiring, under the floor 29

*990-1983*APC Worldwide Customer SupportCustomer support for this or any other APC product is available at no charge in any of the following ways:• Vi

iv 150kW InfraStruXure System—Installation and Start-Up Installation Procedures ... 13Level the PDU and NetShel

150kW InfraStruXure System—Installation and Start-Up vStart-Up Procedure ...31Safety warnings . . . .

150kW InfraStruXure System—Installation and Start-Up 1Safety OverviewSave these instructionsThis manual contains important instructions that must be