American-power-conversion VS 50 User Manual

990-1479E 05/2007 Magnum VS 50 Magnum VS 100 -48 Vdc Power Systems User Manual

Magnum VS –48 Vdc User Manual Page 10 2.3. AC Power Connections WARNING: Ensure that all of the external d

Magnum VS –48 Vdc User Manual Page 11 Each phase should be wired for a minimum of 15 A. The rear cover o

Magnum VS –48 Vdc User Manual Page 12 2.4. Battery Connections WARNING: Hazardous energy levels are pre

Magnum VS –48 Vdc User Manual Page 13 Figure 2.4-1 Battery Cable Connection Locations Battery Temperature Pr

Magnum VS –48 Vdc User Manual Page 14 Figure 2.5-1 CEMF Connection Locations 2.6. DC System Grounding The

Magnum VS –48 Vdc User Manual Page 15 2.7. Load Protection Installation Circuit Breaker Installation Stand

Magnum VS –48 Vdc User Manual Page 16 Circuit Breaker Protected Load Connections (30 or 60 A) The circuit b

Magnum VS –48 Vdc User Manual Page 17 Figure 2.8-3 Bottom Shelf GMT Fuse Connections 2.9. Monitoring and

Magnum VS –48 Vdc User Manual Page 18 Figure 2.9-1 Interface Connections Output Relay 2-6 Connections Out

Magnum VS –48 Vdc User Manual Page 19 RELAY OUTPUT J 411 TERMINAL DESIGNATIONS RELAY ALIAS OUTPUT RELAY NOT

Magnum VS –48 Vdc User Manual Page ii Table of Contents 1 Introduction ...

Magnum VS –48 Vdc User Manual Page 20 2.10. Rectifier Module Installation WARNING: Rectifier output DC ci

Magnum VS –48 Vdc User Manual Page 21 3 Commissioning This section is intended as a guide when powering up a system for the first time. It may n

Magnum VS –48 Vdc User Manual Page 22 3.2. Commissioning Initial Set-up 1. Remove all rectifiers. 2. Disco

Magnum VS –48 Vdc User Manual Page 23 Rectifier Test: 1. To verify that all rectifiers are reporting correc

Magnum VS –48 Vdc User Manual Page 24 Output Relay 1: 1. Minor and Major output relays were tested in the r

Magnum VS –48 Vdc User Manual Page 25 4 Technical Description The Power System is designed to supply safe –54 Vdc primary power through the use of

Magnum VS –48 Vdc User Manual Page 26 System Current Monitor The controller monitors individual rectifier cu

Magnum VS –48 Vdc User Manual Page 27 GMT Fuses When a GMT fuse trips, a fuse element burns out allowing the

Magnum VS –48 Vdc User Manual Page 28 Battery Protection An external disconnect should be mounted at the b

Magnum VS –48 Vdc User Manual Page 29 4.5. Controls and Indicators Controller Module All status monitoring

Magnum VS –48 Vdc User Manual Page iii System Current Monitor...

Magnum VS –48 Vdc User Manual Page 30 5 Operation 5.1. Description The Magnum VS is designed for years of

Magnum VS –48 Vdc User Manual Page 31 J111110 165J5J3J13J9 J8J2J12J4DB9 - RS232 PortMAJORDC GOODMINOROUT RLYV

Magnum VS –48 Vdc User Manual Page 32 Figure 0-1 Magnum VS Controller 5.3. Operation Using the RS-232 Comm

Magnum VS –48 Vdc User Manual Page 33 5.4. Operation Using the 10/100 BaseT Ethernet Port The RJ-45 10/100 B

Magnum VS –48 Vdc User Manual Page 34 Figure 5.5-1 Parameter Locations, Descriptions, and Settings PARAMETER

Magnum VS –48 Vdc User Manual Page 35 PARAMETER NAME/ [MENU LOCATION] DESCRIPTION SETTINGS (Default settings

Magnum VS –48 Vdc User Manual Page 36 PARAMETER NAME/ [MENU LOCATION] DESCRIPTION SETTINGS (Default settings

Magnum VS –48 Vdc User Manual Page 37 PARAMETER NAME/ [MENU LOCATION] DESCRIPTION SETTINGS (Default settings

Magnum VS –48 Vdc User Manual Page 38 PARAMETER NAME/ [MENU LOCATION] DESCRIPTION SETTINGS (Default settings

Magnum VS –48 Vdc User Manual Page 39 PARAMETER NAME/ [MENU LOCATION] DESCRIPTION SETTINGS (Default settings

Magnum VS –48 Vdc User Manual Page iv MAGNUM VS CONTROLLER ...

Magnum VS –48 Vdc User Manual Page 40 PARAMETER NAME/ [MENU LOCATION] DESCRIPTION SETTINGS (Default settings

Magnum VS –48 Vdc User Manual Page 41 5.6. LVD Operation In order to prevent damage to the battery due to dee

Magnum VS –48 Vdc User Manual Page 42 6 Preventive Maintenance Preventive Maintenance is typically performed on a quarterly basis. 6.1. Equipme

Magnum VS –48 Vdc User Manual Page 43 Battery Visual and Safety Inspection Check that the battery temperatur

Magnum VS –48 Vdc User Manual Page 44 Battery Current Test 1. Measure the battery current with a clamp-on m

Magnum VS –48 Vdc User Manual Page 45 6.4. Final Inspection: 5. Verify that the interior and exterior of th

Magnum VS –48 Vdc User Manual Page 46 7 Alarm Summary ALARM/ [MENU LOCATION] DESCRIPTION DEFAULT SETTINGS Battery Discharge Alarm [Batteries/Param

Magnum VS –48 Vdc User Manual Page 47 ALARM/ [MENU LOCATION] DESCRIPTION DEFAULT SETTINGS System LT Alm [Syst

Magnum VS –48 Vdc User Manual Page 48 8 Specifications The overall system specifications can vary, depending upon the number of rectifier modules.

Magnum VS –48 Vdc User Manual Page 49 8.2. DC Output TWF0500H54B Rectifier Output Voltage (factory set)

Magnum VS –48 Vdc User Manual Page 50 Magnum VS 100 Power System Output Voltage (factory programmed) 54.0 Vdc

Magnum VS –48 Vdc User Manual Page 51 8.4. Mechanical TWF0500H54B Rectifier Dimensions (Overall) 5 in (12

Magnum VS –48 Vdc User Manual Page 52 8.6. Compliance NEBS Level 3 (Pending) Safety UL 60950 CE Marked to

Magnum VS –48 Vdc User Manual Page 53 9 APC Worldwide Customer Support Customer Support for this or any other APC product is available at no ch

Magnum VS –48 Vdc User Manual Page 54 10 Limited Product Warranty Two Year Factory Warranty 1 The limited warranty provided by American Power Co

Magnum VS –48 Vdc User Manual Page 6 1 Introduction 1.1. General Information The APC Magnum VS is a modular

Magnum VS –48 Vdc User Manual Page 7 SKU Description DCM00K03SGMT Magnum VS 50, Basic Controller and Integra

Magnum VS –48 Vdc User Manual Page 8 ACDCControlACDCControlACDCControlACDCControlACDCControlGNDL1 L2/NGNDL1 L

Magnum VS –48 Vdc User Manual Page 9 2 Installation 2.1. Unpacking Equipment Remove equipment from packing material and inspect for shipping dama